NI-Motion 8.0f1 Full Win32Eng NI运动驱动程序8.0f1完整版 适用LabVIEW8.2.1~LabVIEW2009
Windows系统下（Linux和MAC系统下请自行了解清楚）NI的各种软件、模块、工具包、驱动程序，使用NI许可证管理器来激活的，绝大部分的都可以使用NI Lincense Activator来激活：NI序列号Serial Number生成激活工具NI License Activator，LabVIEW/VBAI/VDM/VAS等软件模块工具包破解工具不限版本http://visionbbs.com/thread-490-1-1.html视觉论坛的各种NI资源，除了视觉相关的模块有使用外，大部分的都不会使用，仅提供资源不提供技术支持。资源的下载地址一般会同时提供NI官方和百度网盘的地址。某些工具包NI地址失效或没有NI地址，只能使用百度网盘地址；如果百度网盘地址失效过期，可联系论坛客服更新。NI的服务器在美国，有时候速度很慢或下载容易出错，这样会造成安装时各种错误而无法安装。建议在下载完成后，对下载资源做校验和(NI一般会提供MD5或SHA256等)验证，与官方或视觉论坛提供的校验和对比，一致就可以安装；如不一致，则需要重新下载。视觉论坛早期下载上传的资源，基本上都是正常下载的资源；2019后下载的资源，都与NI的正确校验和对比过，保证是正确的资源才上传到百度网盘。校验和工具下载地址：文件Hash计算器FHash，文件校验和验证下载文件正确性验证，MD5值计算、SHA1值计算、SHA256值计算、CRC32值计算http://visionbbs.com/thread-26524-1-1.html
NI-Motion 8.0f1 Full Win32Eng NI运动驱动程序8.0f1完整版 适用LabVIEW8.2.1~LabVIEW2009
NI-Motion为NI运动器件的驱动程序，开发软件为NI SoftMotion，及Motion Assistant。
NI-Motion 8.0f1
发布日期
09-10-1
受支持的操作系统
Windows 2000
Windows Vista 64-bit
Windows Vista
Windows XP
语言
英文
校验和
(MD5)
d00f8c2ed49a02d59209838173ccc4b9
百度网盘下载（限速，请开会员或使用破解限速工具）：
链接: 请注册视觉论坛用户，登录后购买附件下载查看 提取码: 请注册登录视觉论坛会员，购买附件查看
NI官方下载地址（可能无效或无法下载完成）：
请注册登录视觉论坛会员，购买附件查看
NI-Motion™ 8.0f1 Readme for NI 73xx ControllersThis document contains installation and programming considerations for using NI-Motion with NI 73xx motion controllers, a list of changes in this version of NI-Motion, and information about NI-Motion known issues.ContentsGeneral InformationInstallation and Configuration InstructionsNI-Motion 8.0f1 Changes and EnhancementsNI-Motion 8.0f1 General ConsiderationsNI-Motion 8.0f1 Known IssuesPrevious NI-Motion Changes and EnhancementsGeneral InformationNI-Motion 8.0f1 is the motion control software you use to communicate with all National Instruments NI 73xx motion controllers using LabVIEW, C, LabWindows™/CVI™, or Microsoft Visual Basic 6.0 development platforms. Refer to KnowledgeBase article 39DA8HMU, Does the NI-Motion Driver Support Visual Studio .NET?, at ni.com/kb for information about Visual Studio .NET 2003 and Visual Studio 2005 support.NI-Motion 8.0f1 is compatible with the following National Instruments software:
[*]LabVIEW 8.2.1 or later.
[*]LabVIEW Real-Time Module 8.2.1 or later.
[*]LabVIEW NI SoftMotion Module 2009f1 or later.
[*]LabWindows/CVI 7.0 or later.
[*]NI Motion Assistant 2.3 or later graphical prototyping software.
NoteNI-Motion 8.0f1 addresses an issue when using NI-Motion with the LabVIEW NI SoftMotion Module. If you use NI-Motion only with NI 73xx motion controllers, you do not need to update to NI-Motion 8.0f1.Compatibility with Earlier Versions of NI-MotionIf you have developed motion control systems using a previous version of NI-Motion, you must recompile your code before it will work correctly with NI-Motion 8.0f1.In addition, any applications you build in NI-Motion 8.0f1 will not work correctly in earlier versions of NI-Motion. Similarly, configuration settings you build and save in Measurement & Automation Explorer (MAX) with NI-Motion 8.0f1 will not work with applications you build in earlier versions of NI-Motion.LabVIEW Real-Time UsersTo use NI-Motion 8.0f1 with a real-time target, you must update the NI-Motion driver software on the real-time target system using MAX. Driver versions on the host and target system must be the same for proper operation. Refer to the Measurement & Automation Explorer Remote Systems Help by selecting Help»Help Topics»Remote Systems in MAX for information about installing software on the remote system.Back to TopInstallation and Configuration InstructionsThe following sections include important information about installing NI-Motion 8.0f1, instructions for downloading and installing NI-Motion 8.0f1 from the Web or from the CD, and information about NI-Motion firmware.NoteNI-Motion 8.0f1 is supported on Microsoft Windows Vista/XP/2000. If you are using Windows Me/98/NT, do not update to NI-Motion version 8.0. Continue using NI-Motion version 6.1.x.TipFor optimal performance, update your operating system to the latest service pack and apply all security patches. This is especially important on Windows 2000 systems. Refer to KnowledgeBase article 45O8JNHR at ni.com/kb for more information.Downloading NI-Motion 8.0f1 from the WebComplete the following steps to install this update:
[*]Download the NIMotion800f1.exe file, and then run it.
[*]Follow the onscreen instructions.
Note(Windows Vista)Users may see access and security messages during installation. Accept the prompts to complete the installation.
[*]When the installer completes, a dialog box appears that asks if you want to restart, shut down, or restart later. Select Restart.
[*]Download the updated firmware to your controller(s):
NoteYou must update the firmware on your NI 73xx controllers before you can use them with NI-Motion 8.0f1.
[*]Launch MAX.
[*]Expand Devices and Interfaces.
[*]Select the appropriate motion controller.
[*]Click the Firmware tab.
[*]Click the Update Firmware button at the top of the window to update all the firmware files on your device.
Changing Firmware Files to an Earlier Version of NI-MotionFor optimal performance, ensure that the firmware on your controller matches the driver version you install. Complete the following steps to replace the firmware on your controller if you need to use an earlier version of the NI-Motion software and firmware:
[*]Launch MAX.
[*]Expand Devices and Interfaces.
[*]Select the appropriate motion controller.
[*]Click the Firmware tab.
[*]Right-click one of the firmware files in the Firmware Name column and select Download All Files to download the firmware files on the computer onto the controller.
Back to TopNI-Motion 8.0f1 Changes and EnhancementsFixed Issue ID 181673: Incorrect Axis Resources Used With NI SoftMotion Function BlocksA memory allocation error has been found which could result in error -70037 (NIMC_irrelevantAttributeError), movement of the wrong axis, or using the wrong move constraints or target position when making a move.Back to TopNI-Motion 8.0f1 General ConsiderationsInhibit Output BehaviorThe default behavior of the inhibit output changed after NI-Motion 7.0. Previously, the inhibit output would be driven to the active state when the output was disabled. NI-Motion 7.0 and higher drives the inhibit output to the inactive state when the output is disabled. The behavior of the inhibit output when it is enabled did not change.Importing Portable Configuration FilesImporting motion controller settings from older portable configuration files may take a few minutes due to the settings upgrade process. This is expected behavior.Creating C Projects with Microsoft Visual Studio .NET 2003 and Visual Studio 2005Visual Studio .NET 2003 and 2005 do not allow C++ precompiled header files to be used with C source files. Disable precompiled headers when running NI-Motion C examples.National Instruments Software Publisher CertificatesWhen you run setup.exe to install the software from the CD, you are prompted to choose whether you want to always trust software from National Instruments. If you do not select this option, your installation may be interrupted by one or more Microsoft Windows security dialog boxes. However, if you run setup from the command line, you will not receive this prompt, and the installer will automatically install NI's Software Publisher Certificate to the Windows Trusted Publisher Store. If you do not want to make this change to your Windows Trusted Publisher Store, do not choose this installation method.Firmware Versions in NI-Motion 8.0f1The following table lists the expected firmware files that ship with NI-Motion 8.0f1.
Firmware
SectorVersion Number
NI 7330NI 7340NI 7350NI PCI-7390
683317.40.30037.40.30037.40.30037.40.3003
DSP7.31.30027.31.30027.31.30027.31.3002
FPGA17.00.30017.00.30017.10.30017.00.3014
FPGA27.00.30017.00.3001——
Upgrading from NI-Motion 5.0.1When you upgrade NI-Motion 5.0.1 to NI-Motion 8.0f1, your controller does not use the initialization settings you configured and saved in MAX prior to installing NI-Motion 8.0f1. To use your old initialization settings, you must change back to the old settings using the Change Current Settings feature in the Initialization Settings wizard in MAX. Refer to Measurement & Automation Explorer Help for Motion for information about changing device settings.TipClick Help»Help Topics»NI-Motion»NI-Motion Configuration Help to launch Measurement & Automation Explorer Help for Motion.Back to TopNI-Motion 8.0f1 Known IssuesYou can access the software and documentation known issues list online. Refer to the National Instruments Web site for an up-to-date list of known issues in NI-Motion 8.0f1.Back to TopPrevious NI-Motion Changes and EnhancementsRefer to KnowledgeBase article 47CC30FL, NI-Motion Readmes, at ni.com/kb for access to previous NI-Motion readme files, starting with NI-Motion 7.0.Back to TopImportant InformationCopyright© 2009 National Instruments Corporation. All rights reserved.Under the copyright laws, this publication may not be reproduced or transmitted in any form, electronic or mechanical, including photocopying, recording, storing in an information retrieval system, or translating, in whole or in part, without the prior written consent of National Instruments Corporation.National Instruments respects the intellectual property of others, and we ask our users to do the same. NI software is protected by copyright and other intellectual property laws. Where NI software may be used to reproduce software or other materials belonging to others, you may use NI software only to reproduce materials that you may reproduce in accordance with the terms of any applicable license or other legal restriction.TrademarksCVI, National Instruments, NI, and ni.com are trademarks of National Instruments. The mark LabWindows is used under a license from Microsoft Corporation. Other product and company names listed are trademarks or trade names of their respective companies. Refer to the Terms of Use section on ni.com/legal for more information about National Instruments trademarks.PatentsFor patents covering the National Instruments products/technology, refer to the appropriate location: Help» Patents in your software, the patents.txt file on your media, or the National Instruments Patent Notice at ni.com/patents.
页:
[1]