NI GPIB-Serial Converter Software 1.0 Win32Eng NI GPIB到串口转换软件1.0下载
Windows系统下（Linux和MAC系统下请自行了解清楚）NI的各种软件、模块、工具包、驱动程序，使用NI许可证管理器来激活的，绝大部分的都可以使用NI Lincense Activator来激活：NI序列号Serial Number生成激活工具NI License Activator，LabVIEW/VBAI/VDM/VAS等软件模块工具包破解工具不限版本http://visionbbs.com/thread-490-1-1.html视觉论坛的各种NI资源，除了视觉相关的模块有使用外，大部分的都不会使用，仅提供资源不提供技术支持。资源的下载地址一般会同时提供NI官方和百度网盘的地址。某些工具包NI地址失效或没有NI地址，只能使用百度网盘地址；如果百度网盘地址失效过期，可联系论坛客服更新。NI的服务器在美国，有时候速度很慢或下载容易出错，这样会造成安装时各种错误而无法安装。建议在下载完成后，对下载资源做校验和(NI一般会提供MD5或SHA256等)验证，与官方或视觉论坛提供的校验和对比，一致就可以安装；如不一致，则需要重新下载。视觉论坛早期下载上传的资源，基本上都是正常下载的资源；2019后下载的资源，都与NI的正确校验和对比过，保证是正确的资源才上传到百度网盘。校验和工具下载地址：文件Hash计算器FHash，文件校验和验证下载文件正确性验证，MD5值计算、SHA1值计算、SHA256值计算、CRC32值计算http://visionbbs.com/thread-26524-1-1.html
NI GPIB-Serial Converter Software 1.0 Win32Eng NI GPIB到串口转换软件1.0下载
GPIB-Serial Converter Software
GPIB-Serial Converter软件可帮助您配置GPIB仪器控制设备。
GPIB-Serial Converter软件是一个实用程序软件，用于配置GPIB-RS232或GPIB-RS485/RS422转换盒。该实用程序使GPIB仪器控制设备能够将具有RS485、RS422或RS232串行端口的计算机转换为GPIB总线上的讲话者、监听器或控制器。GPIB-Serial Converter软件还为使用GPIB连接第三方仪器提供了最大的可靠性。
1.0Win32Eng
文件大小: 66933024 字节 (63.83 MB)
修改日期: 2010-04-25 03:27
MD5: 4e3398ca7623b29b84f397e2b076a412（官方正确）
SHA1: 369b6fd5a5300e8ff62177298c214d980e1b6678
SHA256: 33d2194578b7a9742cb7eb826a9cd09fd64b5e74d7b5f297afe5237d4e25938b
CRC32: fb82ea8c
百度网盘与NI官方下载地址：
NI GPIB-Serial Converter, Version 1.0© 2006 National Instruments Corporation. All rights reserved.
Thank you for using the NI GPIB-Serial Converter, Version 1.0.
This file contains release notes, patent information, and last-minute information for the NI GPIB-Serial Converter software. Some information in this file may be too recent to be included in the official documentation set.
This readme contains the following main sections:
[*]Release Notes
[*]Features in Version 1.0
[*]Contacting National Instruments
[*]Patent Information
Release NotesThe NI GPIB-Serial Converter software supports the National Instruments GPIB-RS232 and GPIB-RS485/RS422 hardware interfaces. These products are drop-in replacements for the older GPIB-232/485CT-A and GPIB-232CV-A products. There are no dip switches on the GPIB-RS232/485/422 hardware interfaces. The NI GPIB-Serial Converter software allows you to configure the settings for the hardware, as well as update the firmware, if a new firmware image becomes available.Supported InterfacesThe following hardware interfaces are supported:
[*]GPIB-RS232
[*]GPIB-RS485/RS422
The NI GPIB-Serial Converter software must be installed and run on the following operating systems:
[*]Windows 2000 Service Pack 4
[*]Windows XP Service Pack 2
The configured hardware interfaces have been tested with, but are not restricted to, the following:
[*]Windows 2000 Service Pack 4
[*]Windows XP Service Pack 2
[*]32-bit x86 processors
Features in Version 1.0Modes of OperationThe GPIB-RS232/485/422 combines the modes of operation from the GPIB-232/485CT-A (G Mode and S Mode) and GPIB-232CV-A (C Mode and D Mode). Refer to the NI GPIB-Serial Converter Help for additional information regarding each mode.Firmware and Configuration UpdatesUse the NI GPIB-Serial Converter Wizard to select the desired mode of operation and configure the GPIB-RS232/485/422 settings. Download firmware images from the web and use the same utility to update the hardware interfaces with the new firmware.Serial Baud RatesBaud rates up to 115.2 kb/s are supported. Use the NI GPIB-Serial Converter Wizard to configure this setting.Secondary GPIB AddressingSecondary GPIB addressing is available in any mode of operation. Use the NI GPIB-Serial Converter Wizard to configure this setting.EOI Assertion in C ModeIn C Mode, there is an option to assert EOI with <CR> and <LF> termination modes. The EOI (End or Identity) asserts on the GPIB bus on the terminating byte prior to readdressing the device as a Talker. Use the NI GPIB-Serial Converter Wizard to configure this setting.Differences between GPIB-RS232/485/422 and GPIB-232/485CT/CV-ARefer to the NI GPIB-Serial Converter Help for a detailed list of differences between the GPIB-RS232/485/422 and the GPIB-232/485CT/CV-A hardware interfaces.Contacting National InstrumentsThank you for your interest in the NI GPIB-Serial Converter. We appreciate communicating with the people who use our products. We are also very interested in hearing about the applications you develop using our products. Our Web site, ni.com, provides advanced support and services and contact information.Patent InformationFor patents covering National Instruments products, refer to the appropriate location: Help» Patents in your software, the patents.txt file on your CD, or ni.com/patents.
页:
[1]