sample_object_model_3d
— Sample a 3D object model.
sample_object_model_3d( : : ObjectModel3D, Method, SampleDistance, GenParamName, GenParamValue : SampledObjectModel3D)
sample_object_model_3d
creates a sampled version of the 3D object
model ObjectModel3D
which consists of points that have the
minimum distance SampleDistance
to each other.
The created 3D object model is returned in SampledObjectModel3D
.
Using sample_object_model_3d
is recommended if complex point clouds
are to be thinned out for faster postprocessing or if primitives are to be
converted to point clouds.
Note that if the 3D object model is triangulated and should be simplified by
preserving its original geometry as good as possible,
simplify_object_model_3d
should be used instead.
If the input object model ObjectModel3D
contains only points,
several sampling methods are available which can be selected using
the parameter Method
:
The default method 'fast' adds all points from the input model which are not close to any point that was earlier added to the output model. If present, normals, XYZ-mapping and extended point attributes are copied to the output model.
The method 'fast_compute_normals' selects the same points
as the method 'fast' , but additionally calculates the
normals for all points that were selected.
For this, the input object model must either contain normals, which are
copied, or it must contain a XYZ-mapping attribute from which the
normals are computed. The XYZ-mapping is created by
xyz_to_object_model_3d
.
The method 'accurate' goes through the points of the 3D object
model ObjectModel3D
and calculates whether any other points are
within a sphere with the radius SampleDistance
around the
examined point.
If there are no other points, the original point is stored
in SampledObjectModel3D
.
If there are other points, the center of gravity of these
points (including the original point) is stored in
SampledObjectModel3D
.
This procedure is repeated with the remaining points until there
are no points left.
Extended attributes of the input 3D object model are not copied, but
normals and XYZ-mapping are copied.
For this method, a noise removal is possible by specifying a
value for 'min_num_points'
in GenParamName
and GenParamValue
, which removes all
interpolated points that had less than the specified number of neighbor
points in the original model.
The method 'accurate_use_normals' requires normals in the
input 3D object model and interpolates only points with similar
normals.
The similarity depends on the angle between the normals. The threshold
of the angle can be specified in GenParamName
and
GenParamValue
with 'max_angle_diff' .
The default value is 180 degrees.
Additionally, outliers can be removed as described in the method
'accurate' , by setting the generic parameter
'min_num_points' .
The method 'xyz_mapping' can only be applied to 3D object models
that contain an XYZ-mapping (for example, if it was created using
xyz_to_object_model_3d
).
This mapping stores for each 3D point its original image coordinates.
The method 'xyz_mapping' subdivides those original images into
squares with side length SampleDistance
(which is given in
pixel) and selects one 3D point per square.
The method behaves similar to appying zoom_image_factor
onto
the original XYZ-images.
Note that this method does not use the 3D-coordinates of the points for
the point selection, only their 2D image coordinates.
It is important to notice that for this method, the parameter
SampleDistance
corresponds to a distance in pixels, not to a
distance in 3D space as for the other methods.
The method 'xyz_mapping_compute_normals' selects the same points as the method 'xyz_mapping' , but additionally calculates the normals for all points that were selected. If the input object model contains normals, those normals are copied to the output. Otherwise, the normals are computed based on the XYZ-mapping.
If the input object model contains faces (triangles or polygons) or is
a 3D primitive, the surface is sampled with the given
distance.
In this case, the method specified in Method
is ignored.
Note that planes and cylinders must have finite extent.
If the input object model contains lines, the lines are sampled with the
given distance.
The sampling process approximates surfaces by creating new points in the output object model. Therefore, any extended attributes from the input object model are discarded.
For mixed input object models, the sampling priority is (from top to bottom) faces, lines, primitives and points, i.e., only the objects of the highest priority are sampled.
The parameter SampleDistance
accepts either one value, which is
then used for all 3D object models passed in ObjectModel3D
, or one
value per input object model. The unit of the sample distance is the usual
HALCON-internal unit 'm' .
This operator supports cancelling timeouts and interrupts.
ObjectModel3D
(input_control) object_model_3d(-array) →
(handle)
Handle of the 3D object model to be sampled.
Method
(input_control) string →
(string)
Selects between the different subsampling methods.
Default value: 'fast'
List of values: 'accurate' , 'accurate_use_normals' , 'fast' , 'fast_compute_normals' , 'xyz_mapping' , 'xyz_mapping_compute_normals'
SampleDistance
(input_control) real(-array) →
(real / integer)
Sampling distance.
Number of elements: SampleDistance == 1 || SampleDistance == ObjectModel3D
Default value: 0.05
GenParamName
(input_control) string-array →
(string)
Names of the generic parameters that can be adjusted.
Default value: []
List of values: 'max_angle_diff' , 'min_num_points'
GenParamValue
(input_control) number-array →
(real / integer / string)
Values of the generic parameters that can be adjusted.
Default value: []
Suggested values: 1, 2, 5, 10, 20, 0.1, 0.25, 0.5
SampledObjectModel3D
(output_control) object_model_3d(-array) →
(handle)
Handle of the 3D object model that contains the sampled points.
Number of elements: SampledObjectModel3D == ObjectModel3D
gen_box_object_model_3d ([0,0,0,0,0,0,0],3,2,1, ObjectModel3D) sample_object_model_3d (ObjectModel3D, 'fast', 0.05, [], [], \ SampledObjectModel3D) dev_get_window (WindowHandle) visualize_object_model_3d (WindowHandle, SampledObjectModel3D, \ [], [], [], [], [], [], [], PoseOut)
sample_object_model_3d
returns 2 (H_MSG_TRUE) if all parameters
are correct. If necessary, an exception is raised.
read_object_model_3d
,
gen_plane_object_model_3d
,
gen_sphere_object_model_3d
,
gen_cylinder_object_model_3d
,
gen_box_object_model_3d
,
gen_sphere_object_model_3d_center
,
xyz_to_object_model_3d
get_object_model_3d_params
,
clear_object_model_3d
simplify_object_model_3d
,
smooth_object_model_3d
3D Metrology