| Multisim |
| Bug ID | Description |
| 104001 | Deleting label in description box editor with delete key does not delete the label correctly. |
| 105731 | The 4060 CMOS does not simulate correctly under certain conditions. |
| 105751 | The footprint of multisection components cannot be edited after being placed on a schematic. |
| 105787 | When graphing multiple simulations, the post processor might not select the correct time step. |
| 106456 | The spreadsheet view assigns components to non-existent variant under certain conditions. |
| 107063 | The lamp indicator burn out behavior is incorrect. |
| 107287 | Some exported Fourier Analysis results are interpreted as text instead of numbers. |
| 107528 | The 74390 Counter component does not simulate correctly. |
| 107798 | Back annotation does not work if the Refdes does not follow a specific format. |
| 107897 | Certain vacuum tube models do not simulate correctly. |
| 107972 | Monte Carlo and Worst Case analyses do not remember custom tolerances between runs. |
| 107991 | The footprint of an MCU component cannot be changed via it's property pages. |
| 108124 | Digital components cannot be placed within .SUBCKT statements. |
| 108331 | Interactive switches from MSM files cannot be controlled interactively. |
| 108338 | The Network Analyzer cannot load saved settings. |
| 108349 | The ground net can be renamed using the spreadsheet view. |
| 108356 | Disabling database editing does not prevent saving to the database using menu options. |
| 108375 | Setting a restriction on Noise Figure Analysis incorrectly sets the restriction for Batched Analysis. |
| 108383 | Network analyzer pin radio buttons never show that the pins are connected. |
| 108387 | Replace functionality does not work in the Description Box Editor. |
| 108444 | "Pause at the next instruction boundary" does not work for the first simulation after opening a MCU project. |
| 108691 | In Multisim, after loading a file containing placed breadboard components, the components are sometimes missing the top surface. |
| 108811 | Multisim does not check for duplicate layer names against the fixed layer names. |
| 108815 | When printing instruments, the page header with the date, page numbers, and text instrument map are not translated to the selected language. |
| 108820 | Using undo after deleting a component will revert the component's refdes. |
| 108906 | The workspace "Save as" default check box option in Multisim has no effect. |
| 108974 | The coefficient values for the Transfer Function Block get jumbled if the values are sorted by clicking on the Value column. |
| 108980 | The control that allows setting the bus width incorrectly validates the bus width value. |
| 108986 | The transconductance for a Voltage Controlled Current Source in Multisim cannot be negative. |
| 108997 | Trace width min and width max in the Nets tab under the spreadsheet view allow entering invalid characters. |
| 109028 | Disabling one database in the global restrictions incorrectly disables the replace button in component properties. |
| 109077 | The reports spreadsheet and graph do not redraw when scrolling. |
| 109094 | Reverting from the Simplified version in the Educational version of Multisim is not possible. |
| 109103 | Hitting the Enter key when viewing the Customize User Interface dialog box can lock Multisim in customization mode. |
| 109170 | MOSFET "L" and "W" parameters are not accepted in .MODEL statement. |
| 109171 | Multisim crashes if a component's model is changed via the spreadsheet view. |
| 109190 | Setting the Agilent function generator output to square incorrectly limits the offset voltage. |
| 109207 | Exporting to PADS incorrectly sets the Via to Trace clearance. |
| 109235 | The Print button is disabled in the Description Box editor view. |
| 109267 | Undo does not work correctly after performing a "Save As" operation on the circuit. |
| 109308 | Placing subcircuit connectors in the student edition of Multisim is incorrectly not allowed. |
| 109389 | Back annotating works incorrectly for net widths. |
| 109400 | Instruments are not printed correctly when printing using Adobe Distiller 8.1. |
| 109426 | The Ohmmeter cannot be changed to DMM mode during simulation. |
| 109427 | The Database Manager does not allow multi-letter prefixes for the RefDes definition for families. |
| 109455 | Assigning more than one Symbol Pin to the same Model Node fails silently. |
| 109534 | Faults of type 'short' do not behave correctly when used in sub- circuits or hierarchical blocks. |
| 109540 | Data entered into the table for a PWL source is not committed when the Enter key is pressed. |
| 109577 | Rotating or flipping components with an invisible RefDes label incorrectly repositions the label. |
| 109597 | The busline name with spaces is not truncated when defining bus names with the Bus Entry Connect dialog. |
| 109610 | The filter wizard generates an incorrect circuit for certain cases of Chebyshev filter. |
| 109618 | The 0.5 AMP Fuse component does not function correctly. |
| 109886 | Undoing a placed hierarchical connector in subcircuit creates a duplicate pin. |
| 109914 | The POLYNOMIAL_VOLTAGE source sometimes discards coefficient values. |
| 110000 | Using the "Copy to..." option for models in multisection parts does not work correctly. |
| 110075 | The component attributes are not being displayed on a circuit if the locale is set to German. |
| 110133 | Custom simulation settings are not being used if simulation is performed using the Multisim Automation Interface. |
| 110233 | Duplicate printing occurs from the description box editor view |
| 110411 | When replacing an RLC component, the new component cannot be placed exactly in the old location on the schematic |
| 109482 | Locking/unlocking layer in a schematic file will not mark the file as changed. |
| 110215 | Key assignment for certain components is changed to the Space key whenever the S key is first assigned. |
| 110209 | Trace Width Analysis is not reporting pin numbers correctly. |
| 110661 | VOLTAGE_CONTROLLED_CAPACITOR_VIRTUAL and INDUCTOR are missing from the component database. |
| 110545 | Logic analyzer instrument does not load all of the saved data. |
| 110508 | Restoring a project does not refresh the project view in the design toolbox. |
| 110686 | Component 2N7000_SILI has incorrect footprint mapping. |
| 110687 | Component 2SC1815 has incorrect footprint mapping. |
| 110413 | Virtual connections to Off-Page Connectors are not being allowed. |
| 110670 | Multisim does not support inductor .model statements. |
| 110519 | Using undo on a MCU schematic file will not prompt users to save the circuit upon exiting Multisim. |
| 111358 | The footprint for TSSOP-48 is missing pins in Multisim. |
| 111247 | Using the Merge Bus option with a component and a bus crashes Multisim. |
| 111215 | Multisim allows duplicate reference designators in a circuit in some cases. |
| 111036 | Multisim crashes when the Replace By Subcircuit option is used to create a subcircuit that has the same name as a previously deleted subcircuit. |
| 110741 | Buses that connect digital and analog components through subcircuit connections cause Multisim to crash. |
| 110437 | ALTERA_FLBGA672_1.0 footprint does not have enough pins in "Standard Pinout" column. |
| 108084 | Unable to restore a Multisim project backup using built in version control options. |
| 109644 | Noise Density Plot does not show traces in some cases. |
| 109611 | Transfer function component returns incorrect results when used with Transient analysis. |
| 109428 | Using undo in a MCU project circuit will remove the MCU project from the design toolbox in some cases. |
| 109263 | TQPQ64 is missing pin 64. |
| 109045 | The clear pin does not work correctly for the 74LS163N. |
| 108864 | Editing subcircuit symbol automatically toggles certain properties. |
| 109202 | Trace width analysis output does not use the units specified in the PCB Units option in the sheet properties. |
| 111071 | Trace Width settings should be shared by the same nets across different pages. |
| 110998 | Bidirectional component connections not working correctly in 3D view. |
| 110941 | Component editor looses model mapping information under certain conditions. |
| 108677 | The symbol for the NO push-button symbol is incorrect. |
| 108609 | Cancelling MCU placement on a circuit can make the circuit end up in a bad state under certain conditions. |
| 111313 | Performing Undo/Redo in a circuit can reset the settings for LabVIEW instruments in some cases. |
| Ultiboard |
| 103964 | Placing a Power Plane covers a cutout on a board. |
| 105700 | Exporting Gerber files with very long path/file names may overwrite the exported files. |
| 105795 | Ultiboard is not drawing pins on all the layers correctly in Autorouter Mode. |
| 105810 | A netlist does not import correctly into Ultiboard if a required part contained errors. |
| 106200 | Designs with reserved file system characters do not export the NC drill file. |
| 106729 | The Default Layout Colors incorrectly allows user modification. |
| 106804 | Resizing a comment in Ultiboard can sometimes cause the comment to become uneditable. |
| 107213 | Printing to large paper sizes appears to freeze Ultiboard on computers with limited RAM. |
| 107442 | Ultiboard will not save a backup if a file with the name of the backup already exists under some circumstances. |
| 107512 | The selection filter does not save it's state between different sessions of Ultiboard. |
| 107859 | Via layers cannot be changed after placing a via. |
| 107860 | The default path changes when exporting NC drill files. |
| 107868 | Trace shoving does not check whether two nets belong to the same net group before moving them. |
| 107921 | Line segments sometimes become disconnected when moving a trace |
| 107934 | The Results pane search has extra tabs in the search results text if nothing is found on a previous search. |
| 107939 | Searching for part of text does not work in Ultiboard. |
| 107949 | Moving between steps in the Part Wizard sometimes changes the pad size. |
| 107966 | Ultiboard sometimes crashes while showing 3D views. |
| 107997 | Ultiboard crashes after undoing then redoing the Renumber Parts operation. |
| 108005 | Ultiboard might crash if a tooltip was showing when a design was closed. |
| 108006 | The first DRC check performed when loading file is not correct. |
| 108040 | Selecting parts in the Database Manager may add layers to a design. |
| 108054 | After exporting a bill of materials, Ultiboard prevents modification of the destination folder. |
| 108055 | Locking a trace also locks any components associated with the trace's net. |
| 108073 | Forward annotating after grouping parts in Ultiboard creates duplicate parts in Ultiboard. |
| 108102 | Some dialogs do not remember the last selected tab. |
| 108122 | The snap to grid check box should be unchecked by default on the Enter coordinate dialog. |
| 108135 | SVG export does not export THT pads correctly. |
| 108196 | The board outline in Ultiboard erroneously acts as a copper object that can connect nets. |
| 108197 | Thermal reliefs on pads in copper areas are sometimes incorrect. |
| 108208 | Undoing an action in Ultiboard incorrectly undoes the change in the back annotation log. |
| 108246 | Attributes on the silkscreen bottom layer with Windows font do not show correctly when exported to Gerber format. |
| 108248 | Ultiboard complains about the board outline being incomplete while drawing the board outline via coordinates. |
| 108266 | Changing the layer for an attribute does not work. |
| 108291 | Adding copper bottom build-up layers introduces DRC errors in some cases. |
| 108337 | Changing a database password does not prompt for an old password before changing it to the new password. |
| 108392 | Copper areas sometimes do not void correctly. |
| 108409 | Exported SVG cannot be viewed with some 3rd party viewers. |
| 108420 | High speed changes are discarded if the selected net is changed before clicking OK. |
| 108427 | Net names can be incorrectly modified via the spreadsheet view in Ultiboard. |
| 108428 | Entering a trace clearance through the spreadsheet sets an incorrect clearance. |
| 108731 | Importing a DDF file in Ultiboard does not remember the locked status of a component. |
| 108732 | Text is not rotated correctly when importing DDF files. |
| 108851 | The copper area does not connect with ground under certain conditions. |
| 108860 | Ultiboard does not print correctly if the printer is configured to use a high DPI setting. |
| 108931 | A bitmap in a netbridge is drawn in white instead of being drawn in the same color as copper |
| 108933 | Printing with the fit to page option does not work correctly in some cases. |
| 108934 | Bitmaps placed on a copper layer do not have clearances. |
| 108937 | If a copper trace overlaps a board outline, it becomes unmovable. |
| 108972 | The Via clearances are not being saved correctly using the General tab in the Via property pages or the Via spreadsheet tab. |
| 109016 | A layer name containing quotes generates invalid SVG output. |
| 109023 | The solder paste is incorrect when exporting rounded rectangle pads. |
| 109027 | Nesting groups results in pads becoming unconnected. |
| 109091 | Some print settings are not retained between printing sessions. |
| 109095 | Zooming to an area in rapid succession in Ultiboard causes the application to crash. |
| 109147 | Ultiboard does not export slot holes correctly when exporting as an NC Drill file. |
| 109184 | Adding an attribute to a new hole placed on a design that has nothing else on it causes Ultiboard to crash. |
| 109193 | The component wizard does not allow you to type in certain parameters correctly. |
| 109302 | Grouped components are not part of an exported part centroid. |
| 109420 | Reverting changes that create duplicate pin names does not behave correctly. |
| 109422 | The visibility settings of layers are not saved correctly in some cases. |
| 109425 | Single-sided boards are not being routed correctly with the autorouter. |
| 109430 | Rectangular drill holes are showing up as circular in printouts. |
| 109478 | Some columns in the spreadsheet view do not allow changing all the values for that column at the same time. |
| 109486 | The autorouter generates an error when you have a round copper circle on the copper top. |
| 109554 | Zooming in does not center the view to the mouse cursor in some cases. |
| 109579 | Placing a blind via directly below a trace will cut out that trace when printing. |
| 109717 | Component rotations do not behave correctly if a polar grid is used for the design. |
| 109906 | Units in the PCB Properties Pad/Vias tab are not being saved correctly in some cases. |
| 110158 | The lists of Nets are not sorted in the Netlist Editor dialog. |
| 110285 | Copying and pasting a component with a Unicode RefDes does not paste the RefDes correctly. |
| 110291 | Flipping a copper area horizontally or vertically swaps the layer instead. |
| 110317 | Some layers do not show up correctly in the Design Toolbox layers tab in some cases. |
| 110360 | The through hole pad properties field validated data while typing. |
| 109932 | Browsing the design is slow if a large bitmap was placed on the design. |
| 110659 | Opening existing Ultiboard projects resets the PCB units to nm. |
| 109175 | Gerber D does not export files correctly in some cases. |
| 110436 | Ultiboard does not allow setting polar grid smaller than 1 degree. |
| 109416 | Autoplacing with part group in multiple keep-in areas puts Ultiboard in an unrecoverable state |
| 111279 | Selecting show/hide height in 3D view with no design open will crash Ultiboard |
| 110790 | DRC check working incorrectly for objects on the copper bottom layer. |
| 110703 | 3D IGES exports incorrectly in some cases. |
| 111011 | Ultiboard crashes if autorouting with the Netlist Editor left open. |
| 110877 | Autorouter ignores trace length specifications. |
| 109355 | Follow Me router does not use the user defined trace size. |
| 110332 | Footprint does not show up when replaced using Change Shapes option. |
| 108912 | Setting the default favorite layer does not work for Mechanical CAD patterns. |
| 110464 | HTML exports from Ultiboard do not escape reserved HTML characters. |
| 110667 | Values in the Via Cost Factor field are not displayed correctly. |
| 110674 | Design Toolbox and Spreadsheet View are shown when Autorouting regardless of visibility status. |
| 110875 | Export to Excel from the Spreadsheet view fails in some cases. |
| 110408 | Group replica place does not clone the location of attributes. |
| 110254 | SVG html export did not work correctly if the filename contained reserved html characters. |
| 110537 | Horizontal and vertical swap are swapped in the footprint editor. |
| 109161 | Keep-out area saved with a component does not work correctly in some cases. |
| 109022 | The footprint SOT-223 maps incorrectly from Multisim to Ultiboard. |
| 108883 | Ultiboard does not correctly inform the user about the type of vias being placed. |
| 110729 | Values in build-up edit boxes are not displayed correctly. |
| 108936 | Copying and pasting an image in Ultiboard corrupts the Windows clipboard. |
| 110702 | 3D preview and 3D view are not working correctly with board outline holes. |
| 110536 | Entering data for the Via pad diameter without using the up/down arrows behaves erratically. |
| 110789 | DRC error does not report the name of the layer that the object is on. |
| 110745 | 3D IGES is not exporting tops and bottoms of the parts. |
| 110856 | Autorouter fails with a vague error in some cases. |
| 110844 | DRC errors for a picture placed on a copper layer are not being reported correctly. |
| 110823 | Large circles are not drawn correctly in Ultiboard. |
| 110970 | SVG exports from Ultiboard do not represent circles as circle elements. |
| 110893 | The "Use Multiple Clearances" setting in the PCB properties does not behave as expected. |
| 110736 | In Ultiboard, Group Editor/Bus Groups Properties button does nothing. |
发表于 2021-5-31 22:19:16
